View LD2930007_4860023.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LD29300 series
3A, Very low drop voltage regulators
Features

Very low dropout voltage (Typ. 0.4 at 3A) Guaranteed output current up to 3A Fixed voltage with 1% tolerance at 25C Internal current and thermal limit Logic controlled electronic shutdown available in PPAK
TO-220 D2PAK
Description
The LD29300 is a high current, high accuracy, low-dropout voltage regulator series. These regulators feature 400mV dropout voltage and very low ground current. Designed for high current loads, these devices are also used in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes. Typical applications are in Power supply switching
P2PAK/A P2PAK D2PAK/A
post regulation, Series power supply for monitors, Series power supply for VCRs and TVs, Computer Systems and Battery powered systems.
Order codes
Part numbers Packages TO-220 LD29300V15 LD29300D2T18R LD29300V25 LD29300V33 LD29300V50 LD29300D2T50R
(1)
Output voltage P2PAK (1) LD29300P2T15R P2PAK/A LD29300P2M15R LD29300P2M18R LD29300P2M25R LD29300P2T33R LD29300P2T50R LD29300P2T80R LD29300P2M33R LD29300P2M50R LD29300P2M80R LD29300P2M90R(1) LD29300P2MR(1) 1.5 V 1.8 V 2.5 V 3.3 V 5.0 V 8.0 V 9.0 V ADJ
D2PAK
D2PAK/A
LD29300D2M18R LD29300D2M25R LD29300D2M33R LD29300D2M50R
LD29300P2T18R
LD29300V90(1)
LD29300D2T90R(1)
LD29300D2M90R(1)
LD29300P2T90R LD29300P2TR
1. Available on request
June 2007
Rev. 10
1/26
www.st.com 26
LD29300 series
Contents
1 2 3 4 5 6 7 8 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2/26
LD29150
Diagram
1
Figure 1.
Diagram
Schematic diagram for adjustable version
Figure 2.
Schematic diagram for fixed version
* Only for version with inhibit function.
3/26
Pin configuration
LD29300 series
2
Figure 3.
Pin configuration
Pin connections (top view)
TO-220
D2PAK
P2PAK
P2PAK/A
D2PAK/A
* Not connected for fixed version.
4/26
LD29150
Typical application
3
Figure 4.
Typical application
Application circuit
VO = VREF (1 + R1/R2)
* Only for version with inhibit function.
5/26
Maximum ratings
LD29300 series
4
Table 1.
Symbol VI IO PD TSTG TOP
Maximum ratings
Absolute maximum ratings
Parameter DC Input voltage Output current Power dissipation Storage temperature range Operating junction temperature range Value 30 (1) Internally Limited Internally Limited -55 to 150 -40 to 125 Unit V mA mW C C
1. Above 14V the device is automatically in shut-down.
Note:
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Thermal data
Parameter Thermal resistance junction-ambient Thermal resistance junction-case TO-220 50 3 D2PAK-P2PAK-D2PAK/A-P2PAK/A 60 3 Unit C/W C/W
Table 2.
Symbol RthJA RthJC
6/26
LD29150
Electrical characteristics
5
Table 3.
Electrical characteristics
Electrical characteristics of LD29300#15 (IO = 10mA, TJ = 25C, VI = 3.5V, VINH = 2V (Note 2), CI = 330nF, CO = 10F, unless otherwise specified)
Parameter Minimum operating input voltage Output voltage Load regulation Line regulation Supply voltage rejection Test conditions IO = 10mA to 3A, TJ = -40 to 125C IO = 10mA to 3A, VI = 3 to 7V TJ = -40 to 125C IO = 10mA to 3A VI = 3 to 13V f = 120 Hz, VI = 3.5 1V, IO = 1.5A (Note: 1) IO = 1.5A, TJ = -40 to 125C Iq Quiescent current IO = 3A, TJ = -40 to 125C VI = 13V, VINH = GND, TJ = -40 to 125C Isc VIL VIH IINH eN Short circuit current Control input logic low Control input logic high Control input current Output noise voltage VI - VO = 5.5V OFF MODE, (Note 2), TJ = -40 to 125C ON MODE, (Note 2), TJ = -40 to 125C TJ = -40 to 125C, VINH = 13V BP = 10Hz to 100KHz, IO = 100mA 2 5 60 10 65 Min. 2.5 1.485 1.47 0.2 0.06 75 20 45 130 4.5 0.8 50 mA 100 180 A A V V A VRMS 1.5 1.515 V 1.53 1.0 0.5 % % dB Typ. Max. Unit V
Symbol VI VO VO VO SVR
Note:
1 2
Guaranteed by design. Only for version with Inhibit function.
7/26
Electrical characteristics
LD29300 series
Table 4.
Electrical characteristics of LD29300#18 (IO = 10mA, TJ = 25C, VI = 3.8V, VINH = 2V (Note 3), CI = 330nF, CO = 10F, unless otherwise specified)
Parameter Output voltage Load regulation Line regulation Supply voltage rejection Test conditions IO = 10mA to 3A, VI = 3 to 7.3V TJ = -40 to 125C IO = 10mA to 3A VI = 3 to 13V f = 120 Hz, VI = 3.8 1V, IO = 1.5A (Note: 1) IO = 500mA, TJ = -40 to 125C (Note 2) 62 Min. 1.782 1.764 0.2 0.06 72 0.1 0.2 0.4 20 45 130 4.5 0.8 2 5 60 10 0.7 50 mA 100 180 A A V V A VRMS V Typ. 1.8 Max. 1.818 V 1.836 1.0 0.5 % % dB Unit
Symbol VO VO VO SVR
VDROP
Dropout voltage
IO = 1.5A, TJ = -40 to 125C (Note 2) IO = 3A, TJ = -40 to 125C (Note 2) IO = 1.5A, TJ = -40 to 125C
Iq
Quiescent current
IO = 3A, TJ = -40 to 125C VI = 13V, VINH = GND, TJ = -40 to 125C
Isc VIL VIH IINH eN
Short circuit current Control input logic low Control input logic high Control input current Output noise voltage
VI - VO = 5.5V OFF MODE, (Note 3), TJ = -40 to 125C ON MODE, (Note 3), TJ = -40 to 125C TJ = -40 to 125C, VINH = 13V BP = 10Hz to 100KHz, IO = 100mA
Note:
1 2 3
Guaranteed by design. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. Only for version with Inhibit function.
8/26
LD29150
Electrical characteristics
Table 5.
Electrical characteristics of LD29300#25 (IO = 10mA, TJ = 25C, VI = 4.5V, VINH = 2V (Note 3), CI = 330nF, CO = 10F, unless otherwise specified)
Parameter Output voltage Load regulation Line regulation Supply voltage rejection Test conditions IO = 10mA to 3A, VI = 3.5 to 8V TJ = -40 to 125C IO = 10mA to 3A VI = 3 to 13V f = 120 Hz, VI = 4.5 1V, IO = 1.5A (Note: 1) IO = 500mA, TJ = -40 to 125C (Note 2) 55 Min. 2.475 2.45 0.2 0.06 70 0.1 0.2 0.4 20 45 130 4.5 0.8 2 5 100 10 0.7 50 mA 100 180 A A V V A VRMS V Typ. 2.5 Max. 2.525 V 2.55 1.0 0.5 % % dB Unit
Symbol VO VO VO SVR
VDROP
Dropout voltage
IO = 1.5A, TJ = -40 to 125C (Note 2) IO = 3A, TJ = -40 to 125C (Note 2) IO = 1.5A, TJ = -40 to 125C
Iq
Quiescent current
IO = 3A, TJ = -40 to 125C VI = 13V, VINH = GND, TJ = -40 to 125C
Isc VIL VIH IINH eN
Short circuit current Control input logic low Control input logic high Control input current Output noise voltage
VI - VO = 5.5V OFF MODE, (Note 3), TJ = -40 to 125C ON MODE, (Note 3), TJ = -40 to 125C TJ = -40 to 125C, VINH = 13V BP = 10Hz to 100KHz, IO = 100mA
Note:
1 2 3
Guaranteed by design. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. Only for version with Inhibit function.
9/26
Electrical characteristics
LD29300 series
Table 6.
Electrical characteristics of LD29300#33 (IO = 10mA, TJ = 25C, VI = 5.3V, VINH = 2V (Note 3), CI = 330nF, CO = 10F, unless otherwise specified)
Parameter Output voltage Load regulation Line regulation Supply voltage rejection Test conditions IO = 10mA to 3A, VI = 4.3 to 8.8V TJ = -40 to 125C IO = 10mA to 3A VI = 4.3 to 13V f = 120 Hz, VI = 5.3 1V, IO = 1.5A (Note: 1) IO = 500mA, TJ = -40 to 125C (Note 2) 52 Min. 3.267 3.234 0.2 0.06 67 0.1 0.2 0.4 20 45 130 4.5 0.8 2 5 132 10 0.7 50 mA 100 180 A A V V A VRMS V Typ. 3.3 Max. 3.333 V 3.366 1.0 0.5 % % dB Unit
Symbol VO VO VO SVR
VDROP
Dropout voltage
IO = 1.5A, TJ = -40 to 125C (Note 2) IO = 3A, TJ = -40 to 125C (Note 2) IO = 1.5A, TJ = -40 to 125C
Iq
Quiescent current
IO = 3A, TJ = -40 to 125C VI = 13V, VINH = GND, TJ = -40 to 125C
Isc VIL VIH IINH eN
Short circuit current Control input logic low Control input logic high Control input current Output noise voltage
VI - VO = 5.5V OFF MODE, (Note 3), TJ = -40 to 125C ON MODE, (Note 3), TJ = -40 to 125C TJ = -40 to 125C, VINH = 13V BP = 10Hz to 100KHz, IO = 100mA
Note:
1 2 3
Guaranteed by design. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. Only for version with Inhibit function.
10/26
LD29150
Electrical characteristics
Table 7.
Electrical characteristics of LD29300#50 (IO = 10mA, TJ = 25C, VI = 7V, VINH = 2V (Note 3), CI = 330nF, CO = 10F, unless otherwise specified)
Parameter Output voltage Load regulation Line regulation Supply voltage rejection Test conditions IO = 10mA to 3A, VI = 6 to 10.5V TJ = -40 to 125C IO = 10mA to 3A VI = 6 to 13V f = 120 Hz, VI = 7 1V, IO = 1.5A (Note: 1) IO = 500mA, TJ = -40 to 125C (Note 2) 49 Min. 4.95 4.9 0.2 0.06 64 0.1 0.2 0.4 20 45 130 4.5 0.8 2 5 200 10 0.7 50 mA 100 180 A A V V A VRMS V Typ. 5 Max. 5.05 V 5.1 1.0 0.5 % % dB Unit
Symbol VO VO VO SVR
VDROP
Dropout voltage
IO = 1.5A, TJ = -40 to 125C (Note 2) IO = 3A, TJ = -40 to 125C (Note 2) IO = 1.5A, TJ = -40 to 125C
Iq
Quiescent current
IO = 3A, TJ = -40 to 125C VI = 13V, VINH = GND, TJ = -40 to 125C
Isc VIL VIH IINH eN
Short circuit current Control input logic low Control input logic high Control input current Output noise voltage
VI - VO = 5.5V OFF MODE, (Note 3), TJ = -40 to 125C ON MODE, (Note 3), TJ = -40 to 125C TJ = -40 to 125C, VINH = 13V BP = 10Hz to 100KHz, IO = 100mA
Note:
1 2 3
Guaranteed by design. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. Only for version with Inhibit function.
11/26
Electrical characteristics
LD29300 series
Table 8.
Electrical characteristics of LD29300#80 (IO = 10mA, TJ = 25C, VI = 10V, VINH = 2V (Note 3), CI = 330nF, CO = 10F, unless otherwise specified)
Parameter Output voltage Load regulation Line regulation Supply voltage rejection Test conditions IO = 10mA to 3A, VI = 9 to 13V TJ = -40 to 125C IO = 10mA to 3A VI = 9 to 13V f = 120 Hz, VI = 9 1V, IO = 1.5A (Note: 1) IO = 500mA, TJ = -40 to 125C (Note 2) 45 Min. 7.92 7.84 0.2 0.06 59 0.1 0.2 0.4 20 45 130 4.5 0.8 2 5 320 10 0.7 50 mA 100 180 A A V V A VRMS V Typ. 8 Max. 8.08 V 8.16 1.0 0.5 % % dB Unit
Symbol VO VO VO SVR
VDROP
Dropout voltage
IO = 1.5A, TJ = -40 to 125C (Note 2) IO = 3A, TJ = -40 to 125C (Note 2) IO = 1.5A, TJ = -40 to 125C
Iq
Quiescent current
IO = 3A, TJ = -40 to 125C VI = 13V, VINH = GND, TJ = -40 to 125C
Isc VIL VIH IINH eN
Short circuit current Control input logic low Control input logic high Control input current Output noise voltage
VI - VO = 5.5V OFF MODE, (Note 3), TJ = -40 to 125C ON MODE, (Note 3), TJ = -40 to 125C TJ = -40 to 125C, VINH = 13V BP = 10Hz to 100KHz, IO = 100mA
Note:
1 2 3
Guaranteed by design. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. Only for version with Inhibit function.
12/26
LD29150
Electrical characteristics
Table 9.
Electrical characteristics of LD29300#90 (IO = 10mA, TJ = 25C, VI = 11V, VINH = 2V (Note 3), CI = 330nF, CO = 10F, unless otherwise specified)
Parameter Output voltage Load regulation Line regulation Supply voltage rejection Test conditions IO = 10mA to 3A, VI = 10 to 13V TJ = -40 to 125C IO = 10mA to 3A VI = 10 to 13V f = 120 Hz, VI = 11 1V, IO = 1.5A (Note: 1) IO = 500mA, TJ = -40 to 125C (Note 2) 45 Min. 8.91 8.82 0.2 0.06 58 0.1 0.2 0.4 20 50 130 4.5 0.8 2 5 360 10 0.7 50 mA 100 180 A A V V A VRMS V Typ. 9 Max. 9.09 V 9.18 1.0 0.5 % % dB Unit
Symbol VO VO VO SVR
VDROP
Dropout voltage
IO = 1.5A, TJ = -40 to 125C (Note 2) IO = 3A, TJ = -40 to 125C (Note 2) IO = 1.5A, TJ = -40 to 125C
Iq
Quiescent current
IO = 3A, TJ = -40 to 125C VI = 13V, VINH = GND, TJ = -40 to 125C
Isc VIL VIH IINH eN
Short circuit current Control input logic low Control input logic high Control input current Output noise voltage
VI - VO = 5.5V OFF MODE, (Note 3), TJ = -40 to 125C ON MODE, (Note 3), TJ = -40 to 125C TJ = -40 to 125C, VINH = 13V BP = 10Hz to 100KHz, IO = 100mA
Note:
1 2 3
Guaranteed by design. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO+1V applied to VI. Only for version with Inhibit function.
13/26
Electrical characteristics
LD29300 series
Table 10.
Electrical characteristics of LD29300#ADJ (IO = 10mA, TJ = 25C, VI = 3.23 V, VINH = 2V (Note 3), CI = 330nF, CO = 10F adjust pin tied to output pin)
Parameter Minimum operating input voltage Load regulation Line regulation Reference voltage Test conditions IO = 10mA to 3A, TJ = -40 to 125C IO = 10mA to 3A VI = 2.5 V to 13V IO = 10mA to 3A, VI = 2.5 to 4.5V TJ = -40 to 125C (Note 2) f = 120 Hz, VI = 3.23 1V, IO = 1.5A (Note 1) IO = 1.5A, TJ = -40 to 125C -1% -2% 65 75 20 45 130 50 mA 100 180 1 4.5 0.8 2 5 50 10 A A A V V A VRMS Min. 2.5 0.2 0.06 1.23 1.0 0.5 +1% V +2% dB Typ. Max. Unit V % %
Symbol VI VO VO VREF SVR
Supply voltage rejection
Iq
Quiescent current
IO = 3A, TJ = -40 to 125C VI = 13V, VINH = GND, TJ = -40 to 125C
IADJ Isc VIL VIH IINH eN
Adjust pin current Short circuit current Control input logic low Control input logic high Control input current Output noise voltage
TJ = -40 to 125C (Note 1) VI - VO = 5.5V OFF MODE, (Note 3),TJ = -40 to 125C ON MODE, (Note 3), TJ = -40 to 125C TJ = -40 to 125C, VINH = 13V BP = 10Hz to 100KHz, IO = 100mA
Note:
1 2 3
Guaranteed by design. Reference voltage is measured between output and GND pin, with ADJ PIN tied to VOUT. Only for version with Inhibit function.
14/26
LD29150
Typical characteristics
6
Figure 5.
Typical characteristics
Output voltage vs temperature Figure 6. Dropout voltage vs temperature
Figure 7.
Dropout voltage vs output current
Figure 8.
Quiescent current vs output current
Figure 9.
Quiescent current vs output current Figure 10. Quiescent current vs supply voltage
15/26
Typical characteristics
LD29300 series
Figure 11. Quiescent current vs temperature
Figure 12. Quiescent current vs temperature
Figure 13. Short circuit current vs temperature Figure 14. Supply voltage rejection vs temperature
Figure 15. Stability vs CO
Figure 16. Line transient
VI=3.5 to 5.5V, ILOAD=10mA, VO=2.5V, CO=10F
16/26
LD29150
Typical characteristics
Figure 17. Load transient
VI=4.5V, IO=10mA to 3A, VO=2.5V, CO=47F
17/26
Package mechanical data
LD29300 series
7
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.
18/26
LD29150
Package mechanical data
TO-220 (A TYPE) MECHANICAL DATA
DIM. A b b1 c D E e e1 F H1 J1 L L1 L20 L30 P Q 3.75 2.65 mm. MIN. 4.40 0.61 1.15 0.49 15.25 10.0 2.4 4.95 1.23 6.2 2.40 13.0 3.5 16.4 28.9 3.85 2.95 0.147 0.104 TYP MAX. 4.60 0.88 1.70 0.70 15.75 10.40 2.7 5.15 1.32 6.6 2.72 14.0 3.93 MIN. 0.173 0.024 0.045 0.019 0.600 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 0.645 1.138 0.151 0.116 inch TYP. MAX. 0.181 0.034 0.067 0.027 0.620 0.409 0.106 0.203 0.051 0.260 0.107 0.551 0.154
0015988/N
19/26
Package mechanical data
LD29300 series
D2PAK MECHANICAL DATA
mm. DIM. MIN. A A1 A2 B B2 C C2 D D1 E E1 G L L2 L3 M R V2 0 4.88 15 1.27 1.4 2.4 0.4 8 0 10 8.5 5.28 15.85 1.4 1.75 3.2 0.192 0.590 0.050 0.055 0.094 0.016 8 4.4 2.49 0.03 0.7 1.14 0.45 1.23 8.95 8 10.4 0.393 0.335 0.208 0.624 0.055 0.068 0.126 TYP MAX. 4.6 2.69 0.23 0.93 1.7 0.6 1.36 9.35 MIN. 0.173 0.098 0.001 0.027 0.044 0.017 0.048 0.352 0.315 0.409 TYP. MAX. 0.181 0.106 0.009 0.036 0.067 0.023 0.053 0.368 inch
P011P6G
20/26
LD29150
Package mechanical data
D2PAK/A MECHANICAL DATA
mm. DIM. MIN. A A1 A2 B B1 B2 C C2 D D1 E E1 G L L2 M R V2 0 4.88 15 1.27 2.4 0.4 8 0 10 8.5 5.28 15.85 1.4 3.2 0.192 0.591 0.050 0.094 0.016 8 4.40 2.49 0.03 0.7 0.8 1.14 0.45 1.23 8.95 8 10.4 0.394 0.335 0.208 0.624 0.055 0.126 TYP MAX. 4.60 2.69 0.23 0.93 1.3 1.7 0.60 1.36 9.35 MIN. 0.173 0.098 0.001 0.028 0.031 0.045 0.018 0.048 0.352 0.315 0.409 TYP. MAX. 0.181 0.106 0.009 0.037 0.051 0.067 0.024 0.054 0.368 inch
7106164/D
21/26
Package mechanical data
LD29300 series
P2PAK MECHANICAL DATA
mm. DIM. MIN. A A1 A2 b c c2 D D2 E E1 e e1 L L2 L3 L5 R V2 0 3.20 6.60 13.70 1.25 0.90 1.55 0.40 8 0 10.00 8.5 3.60 7.00 14.50 1.40 1.70 2.40 0.126 0.260 0.539 0.049 0.035 0.061 0.016 8 4.30 2.40 0.03 0.80 0.45 1.17 8.95 8 10.40 0.393 0.334 TYP MAX. 4.80 2.80 0.23 1.05 0.60 1.37 9.35 MIN. 0.169 0.094 0.001 0.031 0.017 0.046 0.352 0.315 0.409 0.409 0.142 0.275 0.571 0.055 0.067 0.094 TYP. MAX. 0.188 0.110 0.009 0.041 0.023 0.053 0.368 inch
7226255/B
22/26
LD29150
Package mechanical data
P2PAK/A MECHANICAL DATA
mm. DIM. MIN. A A2 C D D1 E F G G1 H1 H2 L L1 L2 M R V2 0 1.27 2.4 0.40 8 0 10.00 15 8 1.40 3.2 0.050 0.094 0.016 8 4.30 0.03 1.17 2.40 8.95 0.45 0.80 3.20 6.60 8.5 10.40 15.85 0.393 0.590 0.315 0.055 0.126 TYP MAX. 4.80 0.23 1.37 2.80 9.35 0.60 1.05 3.60 7.00 MIN. 0.169 0.001 0.046 0.094 0.352 0.017 0.031 0.126 0.260 0.334 TYP. MAX. 0.188 0.009 0.053 0.110 0.368 0.023 0.041 0.142 0.275 0.409 0.409 0.624 inch
7157127/A
23/26
Package mechanical data
LD29300 series
Tape & Reel D2PAK-P 2PAK-D 2PAK/A-P 2PAK/A MECHANICAL DATA
mm. DIM. MIN. A C D N T Ao Bo Ko Po P 10.50 15.70 4.80 3.9 11.9 10.6 15.80 4.90 4.0 12.0 12.8 20.2 60 14.4 10.70 15.90 5.00 4.1 12.1 0.413 0.618 0.189 0.153 0.468 0.417 0.622 0.193 0.157 0.472 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.421 0.626 0.197 0.161 0.476 0.512 MIN. TYP. MAX. 7.086 0.519 inch
24/26
LD29150
Revision history
8
Table 11.
Date
Revision history
Revision history
Revision 7 8 9 10 Order Codes Has Been Updated. Order codes has been updated and the document has been reformatted. Order codes has been updated. Order codes has been updated. Changes
21-Oct-2005 10-Apr-2007 11-May-2007 08-Jun-2007
25/26
LD29300 series
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
26/26

▲Up To Search▲

Price & Availability of LD2930007

	To Download LD2930007 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .